Unthread the black plastic cap by hand, and remove/change the wire drive roller. Once you set up the welder yourself a few times, it will become second nature, and you'll be able to do it in a flash on any occasion. It can be used to weld MIG (GMAW), Stick (SMAW), Gasless (FCAW), as well as TIG (GTAW). Unlike solid wire, the flux-cored wire requires the W-Groove roller. Lightweight yet heavy-duty portable design allows you to take your YesWelder from the workshop to the worksite and beyond. MP200 5-in-1 welder & cutter User Guide | YesWelder MIG - CHART - YesWelder YesWelder MP200 additionally enables you to reduce at the same time. Luckily, like some other YesWelder machines, such as 250DS, or TIG-250P, MP200 features plastic control panel protection. Many more modern machines offer front panel polarity settings, but with YesWelder MP200, you will have to open the wiring compartment. It can be used to bond MIG (GMAW), Stick (SMAW), Gasless (FCAW), as well as TIG (GTAW). Like any arc welding machine, the MP200 requires you to correctly set up the polarities to initiate the arc in a closed electric circuit. The Stick welder feature is just that, sticky. Shop our online store. Never weld or cut if you are feeling unwell or if your state of awareness is down. Keep in mind that a smooth roller is not capable of guaranteeing the stable flux-cored wire feed. On the other hand, most popular multi-process welders, such as Hobart Multi-handler 200, Lincoln PowerMIG 210MP, Eastwood MP200i, or Everlast MTS211SI, are spool-gun ready. Commonly used tungsten electrodes are: pure tungsten, thoriated, lanthanated, ceriated, zirconated, and the rare earth mix tungsten electrodes. Continuously learn and research welding safety. You get everything you need to weld straight out of the box, including the decent but bulky MIG, TIG, and Plasma cutting torches with consumables, as well as a Stick electrode holder. The flux-cored wire installation process is identical to the solid MIG wire installation process described earlier, with one crucial difference. Make sure these connections are tight so that there is no gas leakage. Repeat the same process with the other end of the air hose and the air inlet on the back of the welder with the wording "CUT GAS." The YesWelder MP200 is an inverter welder based on IGBT inverter technology. So, the original idea behind the YesWelder MP200 is to get the best value out of one machine. NEW! YesWelder Firstess MP200 Review/Setup/Operations Guide - YouTube That means your arc will remain stable, weld clean, and bead smooth. Never use oxygen, acetylene, carbon dioxide, combustible gases, or any other bottled gas because this can cause an explosion and serious injuries or death. Follow the guidelines for installation, operation, maintenance, and troubleshooting to ensure personal safety and optimal equipment performance. YesWelder M800h User Manual - Quality Welding Equipment & Discount Code In addition, maximum clean cut thickness is rated at 0.27 at 220V or 0.19 at 110V at maximum output power. A revolution into multi-process machines, YesWelder MP200, offers a plasma cutting option. Upon entering the MIG welding mode in the main menu on display, you will see your current and voltage settings, the polarity, and the upper row with additional settings. Afterward, you can select your process. Thats less than you would expect, as brand-name welders such as Hobart, Miller, or Lincoln usually grant a five or three-year warranty. Subscribe to get special offers, free giveaways, and once-in-a-lifetime deals. This will initiate the arc, and by dragging the torch, you will be slicing through metal. The MP200 is a versatile and also powerful 5-in-1 welding device particularly created for house DIY or maintenance tasks. The ground clamp is plugged in the first Dinse socket; bottom left, where the ground clamp symbol is located. In addition, to swap between MIG and Flux Core welding, you will have to switch polarity. The MP200 is a versatile and powerful 5-in-1 welding equipment specially created for residence DIY or upkeep projects. Search YESWELDER EH-091X Auto Darkening Welding Helmet Instruction Manual Learn how to operate the EH-091X Auto Darkening Welding Helmet with this comprehensive instruction manual. So, just as when setting up the MIG, loosen the feed tensioner and pull it downwards. Pressurized gas cylinders are dangerous, and you should abide by all safety measures to prevent hazards. You don't have to worry about the polarity because it can't be reversed. All the images are intuitive and easy to recognize; you need to turn to the knob and select the right one.Some additional options vary depending on the process. Right from your home. Only qualified persons should operate and maintain this unit. The stick welding process works with the DCEP or DCEN polarity, and its selection is primarily influenced by the desired results and the stick electrode. Make your dream projects a reality with a versatile machine for MIG, FCAW, MMA, TIG welding and plasma cutting. YesWelder stepped up the game by making MP200, a 5 in 1 welder that combines the four most popular welding processes, and plasma cutter, into one lightweight and portable machine. It consists of three main parts: a feed tensioner, idler arm, and a feed roller knob. Stay safe while operating the CUT-45DS Air Plasma Cutter from YESWELDER. Customer focused. Great beginner/ home hobbyist welder for your buck. I am aware digital display can be a liability in busy workshops whit sparks and debris flying around. Yeswelder FIRSTESS MP200 Review - [Detail Look] - Weld Guru It can be made use of to bond MIG (GMAW), Stick (SMAW), Gasless (FCAW), and TIG (GTAW). YesWelder FIRSTESS MP200 5-in-1 Welder & CutterYesWelder Quality welding equipment. It provides better quality than most in its price range, directly competing with some of the top multi-process units. Push the freshly made tip into the wire feeding mechanism all the way through to enter the MIG gun. Remember that you dont have all the fancy TIG settings on the screen, as the gas is not running directly through the welder. YesWelder Auto Darkening M800h User Manual - Quality Welding Equipment YesWelder FIRSTESS MP200 5-in-1 Welder & Cutter with Consumables Pack - YesWelder User Manual. As a YesWelder affiliate, I earn commissions for qualifying purchases. To successfully MIG weld, you have to use a DCEP polarity, which means that your welding electrode (MIG wire) is positive, and your ground clamp is negative. The first thing you notice when looking at the YesWelder MP200 is a sturdy case. You will also need to wear safety glasses underneath your welding helmet. It allows you to store up to 10 different voltage and current settings for each welding type. The Eastwood MP200i is a semi-professional multi-process welder with an emphasis on arc quality and ease of use. On the other hand, the amperage goes down to 20 amps, meaning you shouldnt weld materials thinner than 18 ga. Subscribe to get special offers, free giveaways, and once-in-a-lifetime deals. Image source: https://www.slideserve.com/jaden/chm-605-1221234. YesWelder MP200 is equipped with an intuitive 4.3 high-pixel display. I've welded many times over the years but my welds were mediocre at best. The MP200's 4.3'' high-pixel display puts everything you need on one big, bright, colorful screen. Tighten the hose clamp firmly with a wrench or a socket but not too tight to damage the hose. We recommend using MP200 with a 75/25 mixture and a standard 75/25 gas regulator, because that way, you are unlikely to make a mistake. The MP200 is a versatile and powerful 5-in-1 welding machine specially designed for home DIY or maintenance projects. The YesWelder Firstess MP200 supports a lift TIG arc start, which is a relatively clean process compared to the scratch start. I reached out to Yeswelder, explained what happened. Still, it weighs only 25 lbs, making it lighter than Eastwood MP200i with 34 pounds, Lincoln PowerMIG 200 MP with 40 lbs, and Hobart Multi-Handler 200 with 38.4 lbs. Ive never had problems with the feed regarding the mechanism in the past. Tungsten electrodes are classified according to their principal oxide and its percentage of the total electrodes' mass. You can only set the amperage, and you control the post-flow and pre-flow by using the TIG torch valve. The duty cycle is rated at 60%, as most multi-process . Before we move on to a detailed explanation of how to set up the welder, let's explain some of its features and their purpose. You can install it easily on the back of the welder. I'm quite impressed with the Yes Welder 250A. So, you need to thread the air compressor inlet connection and the brass barb for the air outlet according to the designated airflow. 1. The MP200 will display both imperial and metric units, making it easy to use for the welder worldwide. Users are advised to read the manual carefully before operation. Next, place the cutting tip over the two and thread the shielding cap over everything to the threads on the outside of the torch head. The left knob modifies the amperage output, wire feeding speed, and voltage settings in synergy, while the right knob allows you to manually fine-tune the voltage settings. Widely used in various industries, this helmet protects welders from electricity arc and is suitable for temperatures between -10C to 60C. Click to play video. On the other hand, other budget units such as Eastwood MP200i and Everlast Power MTS200SI provide smaller rollers capable of running 0.023-0.030 wire, while Everlast doesnt offer a separate flux core wire roller. YESWELDER 8-Inch Welding Pliers, Rentention Chain, Anti-Rust MIG YESWELDER, was born from a vision to provide affordable and high-quality welding equipment to those entering and experienced in the world of welding. The problems ?? Getting the best value out of the money spent is one of the first things you should consider before buying any welder. YesWelder YWM-211P Double Pulse Aluminum MIG Welder . This means that to run any of its five processes, you must connect the ground clamp to the metal and use the MIG/TIG/Stick/Plasma torch to close the circuit. YesWelder FIRSTESS MP200 Multiprocess 5-in-1 Welder - YouTube Videos for related products. Nevertheless, it wont suit the welders that like to tackle the more serious projects and thicker materials or aluminum. We've seen it all now! Before you tighten it with your hand, adjust the length of the protruding tungsten by sliding it back and forward. Your destination for quality welding equipment. With the help of our strong welding community, we strive to make products that are designed with every level of welder in mind- from beginners to hardcore hobbyists to those that do this for a living. The Control panel features a large, intuitive display which is pretty straightforward, while synergic controls make it even easier to use. You can find a similar feature in a couple of times more expensive Miller Multimatic 210. The plasma cutting specifications are below: Output Current 110V: 20-30A, 220V: 20-40A, Max clean cut 110V: 0.19" (5mm) at 30A, 220V: 0.27" (7mm) at 40A, Max severance cut 110V: 0.31" (8mm) at 30A, 220V: 0.5" (12.7mm) at 40A. Designed for use with welding power sources and generators, the Remote Foot Control can be located up to 200 feet away from the source using included or similar type cords. When MIG welding with this mixture, the penetration will be broader but less deep than with 100% CO2, making it a better choice for thin metal. On the other hand, most multi-process welders are DC-only machines. Easy to learn for beginners, and powerful and capable enough for the pros. You should continually educate yourself further and work on hazard prevention. So, let's get started by explaining the MIG setup first. Makers and hobbyists searching for a powerful welder and cutter specifically designed for DIY projects may be interested in the powerful YesWelder FIRSTESS . After the welder is plugged into your 110V or 220V outlet, simply switch the button to on state, and the welder will turn on. After you line up the connections, push the MIG gun connection into the unit and tighten the threaded collar to make an air-tight connection. When choosing a TIG welding, you can use a max input current of 30A at 110V or 21.6A at 220V. The air filter needs to be mounted at the back of the MP200, connected with the air compressor and the MP200 air inlet. Before you start plasma cutting, you can select the gas pre-flow and post-flow duration. Nevertheless, considering 1 year warranty, I dont recommend you test it. We recommend an air compressor with an output of 9-12CFM @ 78 PSI. Image source: https://ehs.uci.edu/safety/pdfs/compressed-gas-reference-guide.pdf. Learn how to safely and effectively use the YESWELDER Foot Pedal with this comprehensive instruction manual. YesWelder FIRSTESS MP200 5-in-1 Welder & Cutter with Consumables Pack - YesWelder User Manual. Thats the case with Miller Multimatic 200, Lincoln PowerMIG 200 MP, and Everlast MTS211SI. However the Tig setup doesn't belong on this welder if you aren't going to have the hot start circutry. Always keep them chained up to a secure place in the upright position and place the protective cap back on when they are not in use or during any transport. This user manual is for the YesWelder MIG-205DS IGBT inverter multi functions welding machine, which is produced under Chinese & International quality standards. The arrow on the air filter points in the direction of the airflow. Discover its features, including adjustable shade value and IR/UV filters for improved safety. Every electrode has a specified polarity it will work with. YesWelder MP200 includes an 8-foot gas hose with 5/8"-18 RH fitting. Barry of @Jo Daddy's Garage giving us a full walkthrough of the YesWelder Firstess MP200 5in1 Welder \u0026 CutterEquipment used: https://yeswelder.com/products/firstess-mp200Outline:0:00 - Introduction1:20 - Unboxing3:07 - Parts Introduction6:47 - Back Panel Introduction7:28 - Oil-Water Separator11:17 - Air Supply for Plasma Cutting Installation12:52 - Inside the MP20013:05 - Polarity Connection14:13 - Front Panel Connection17:00 - TIG Setup Details20:53 - Plasma Cutting Setup Details23:25 - Plasma Cutter Gun24:52 - Argon/CO2 for TIG Connection26:33 - Wire Feeder31:18 - MIG Wire Fast Feeding32:27 - Controls33:40 - MMA Settings34:50 - MIG Settings37:40 - FCAW Settings38:22 - Lift TIG Settings39:03 - Plasma Cut Settings40:00 - Ground Clamp SettingsABOUT YesWelder: YesWelder specializes in designing and manufacturing state-of-the-art welding machines, helmets, and accessories enjoyed by those with a passion for welding.